Skid Steer Snow Attachment Rentals: Pushers, Blades and Blowers

Pablo Fernandez
Pablo Fernandez
November 16, 2026
Skid Steer Snow Attachment Rentals: Pushers, Blades and Blowers

The forecast says 8 inches on Thursday, the lot is half an acre, and the one attachment every yard still has in stock is the wrong one for your site.

A pusher too wide for the machine stalls it on the first pass. A blower on a standard-flow skid steer spits snow a few feet and bogs. A steel cutting edge on stamped concrete leaves scrapes you'll be looking at in April. Snow work punishes a bad match, and the storm doesn't wait while you swap.

Here's how to match a skid steer snow pusher, blade or blower to your lot, your snow and your machine's hydraulics, then what to reserve before the first storm is on the radar.

Three Attachments, Three Jobs

Each snow attachment moves snow a different way, and the way it moves snow is what decides where it belongs.

Pushers

A pusher is a box. A straight moldboard with side plates on each end, it contains the snow in front of the machine and moves the whole pile in a straight line to wherever you're stacking it. No windrow, no spill off the sides, no second pass to clean up. On a wide open lot with long runs, nothing moves more snow per hour for the money.

Blades

A blade angles. A plow blade on a skid steer works like the one on a pickup: set it at an angle and it rolls the snow off to one side as a windrow. V-blades add a wedge position for breaking through deep or drifted snow and a scoop position for carrying. Blades are the tool for driveways, drive lanes, sidewalks and anywhere you need to move snow sideways rather than forward.

Blowers

A blower throws. An auger feeds snow into an impeller that fires it out a chute, typically 30 to 45 feet depending on the model and the snow. It handles deep, drifted and already-piled snow that a pusher or blade would just climb over, and it's the only option when there's nowhere on the site to stack a pile. It's also the slowest per square foot of the three, and the most demanding on the machine.

Match the Attachment to the Lot

Lot size and lot shape point to different attachments, and the machine you're renting sets the ceiling on width.

Width Against the Machine

Pusher width follows machine size, not ambition. One major pusher manufacturer's sizing chart for skid steers calls for a minimum of 46 horsepower and 5,500 pounds of machine weight for an 8-foot pusher, 70 horsepower and 7,000 pounds for a 10-foot and 85 horsepower and 10,000 pounds for a 12-foot. Other makers' charts land in the same neighborhood. The weight matters as much as the power: a light machine behind a wide pusher full of wet snow spins its tires or tracks and goes nowhere.

  • Mini and small-frame machines (roughly 1,500 to 1,750 pounds rated operating capacity): 6- to 8-foot pushers, 7- to 8-foot blades.
  • Mid-frame machines (roughly 1,750 to 2,500 pounds ROC): 8- to 10-foot pushers, 8- to 9-foot blades, standard-flow blowers up to about 72 inches.
  • Large-frame machines and compact track loaders over 2,500 pounds ROC: 10- to 12-foot pushers, 9- to 10-foot blades, high-flow blowers at 72 to 84 inches.

Treat those as starting points and check the listing against the attachment's own spec. Read more about what size skid steer you need and rated operating capacity.

Lot Shape and Obstacles

Open lots want a pusher, cluttered ones want a blade. A retail or warehouse lot with long rows and a pile location at one end is pusher territory. Add parking islands, light poles, loading docks, curbs and a drive lane that has to stay open, and the blade's ability to angle and windrow starts winning. Most commercial sites end up needing both, with the pusher doing the volume and the blade doing the edges and the entrances.

Pile space decides whether a blower is in play at all. If the lot has room to stack snow along one edge, a pusher gets it there faster. If it doesn't, or if the pile has grown past what the machine can push up, the blower is the way to move snow somewhere else.

A Worked Example

A half-acre lot is about 21,800 square feet. A 10-foot pusher on a mid-frame skid steer moving at a walking pace of 3 mph covers roughly 10 feet by 264 feet a minute, or about 2,600 square feet, before you account for turning, stacking and the fact that 8 inches of snow fills a pusher fast. Call it 15 to 25 minutes of pushing for the open area under good conditions, then another stretch of blade work on the entrances and around the islands. Double it for wet snow. If that same lot is a maze of islands, the pusher's advantage mostly disappears and the blade does the work in more passes.

Match the Attachment to the Snow

The same 8 inches can be two very different loads, and the attachment that handled last month's powder might not handle this week's.

Snow Weight

Wet snow is several times heavier than powder. Fresh, dry snow runs somewhere around 5 to 12 pounds per cubic foot. Wet or compacted snow can run well over 20, and slush and refrozen snow higher still. A 10-foot pusher holding a pile 3 feet deep and 2 feet thick in front of the blade is carrying 60 cubic feet, which is a few hundred pounds of powder or over 1,000 pounds of wet March snow. That's the difference between a machine that pushes and one that spins. When heavy snow is forecast, size the pusher a step down or plan on shorter runs.

Depth and Drifting

Pushers and blades like to take snow in passes; blowers like to take it in one. A pusher loses efficiency once the snow is deeper than the moldboard can contain, and a blade rides up and over hard drifts instead of cutting them. Past about a foot of accumulation, plan on two passes with a pusher or blade, or switch to a blower for the deep sections and the drift lines along fences and buildings. Blowers handle depth without complaint but move slowly, so use them where the depth is, not across the whole lot.

Ice, Hardpack and the Cutting Edge

The cutting edge decides what the attachment scrapes and what it skips over. Steel edges bite into hardpack and refreeze and leave a cleaner surface, and they scratch anything decorative. Rubber and polyurethane edges flex over pavers, stamped concrete, manhole covers and expansion joints without marking them, and they leave a thin film of snow behind on hardpack. Trip edges, which fold back when they hit a curb or a frozen rut, protect the machine and the surface and are worth asking for on any site with raised edges. If the lot has a mix, rent the rubber edge and plan on a deicer for the film.

Hydraulics Decide Whether a Blower Will Work

Pushers and most blades don't need auxiliary hydraulics at all; the machine's lift and tilt do the work. Blowers are different, and this is where most snow attachment rentals go wrong.

Standard flow runs roughly 15 to 25 gallons per minute. High flow starts above that and runs past 40. A blower's auger and impeller run off the auxiliary hydraulic circuit, and most full-size blowers are built for high flow. Put one on a standard-flow machine and it will turn, but it won't throw, and in wet snow it will stall. Some smaller blowers are rated for standard flow and work fine on the right machine. Either way, the attachment's flow requirement and the machine's flow rating both need to be on the listing, and they need to match before you book.

  • Check the machine listing for "high flow" or a gpm figure.
  • Check the blower's spec for its minimum flow and pressure.
  • Confirm the coupler style and the number of hydraulic functions; a blower chute rotator needs a third function or an electric kit.
  • Hydraulically angled blades need an auxiliary circuit too, though standard flow is plenty.

Read more about skid steer attachments explained and about how to change attachments on a skid steer or mini excavator.

What to Reserve Before the Storm

Snow attachments are seasonal inventory with a seasonal rush. The week a storm is on the forecast, every pusher and blower in the area is spoken for by the people who booked in October.

Book the Attachment and the Machine Together

The match is the reservation. Reserve the machine and the attachment as one package so the coupler, hydraulic flow and width are confirmed before anything shows up. An 8-foot pusher that arrives for a machine that could have run a 10-foot costs you time every pass; a blower that arrives for a standard-flow machine costs you the storm.

Rent by the Week or the Season

A storm cycle is longer than a day. Between the storm, the cleanup, the refreeze and the next system behind it, a daily rate rarely makes sense for snow work. Weekly rates cover a cycle, and a monthly rate covers a stretch of winter for less than you'd pay in daily rentals on a bad month. Read more about how daily, weekly and monthly rates work on equipment rentals.

Tracks, Wheels and Getting It to the Site

Tracks float, wheels grip. Compact track loaders ride over deep snow and soft ground where a wheeled machine sinks, and wheeled skid steers with snow tires or chains hold better on ice and plowed pavement and turn without tearing up the surface. Which one belongs on your site is its own decision. Read more about renting a skid steer or compact track loader for snow removal. If you're hauling the machine yourself rather than taking delivery, read more about equipment trailer rentals for hauling snow equipment in winter.

A Note on Insurance

Operating rented equipment is different from towing a trailer, so check with your insurer about coverage for renting and running a machine, and review our FAQ and platform terms for how equipment rentals work before you book.

Ready for the First Storm?

Pick the attachment for the lot, size it for the machine and the snow, confirm the hydraulics and get the reservation in before the forecast does it for you. Browse compact track loader rentals near you, or wheeled skid loaders if your site is mostly pavement.

The Short Version

  • Pushers move volume in straight lines on open lots. Blades angle and windrow around obstacles. Blowers throw deep or drifted snow where there's no room to pile.
  • Size the pusher to the machine: roughly 8 feet for small-frame, 10 feet for mid-frame, 12 feet for large-frame; check the maker's horsepower and weight minimums.
  • Wet snow weighs several times what powder does. Size down or run shorter passes when heavy snow is forecast.
  • Rubber or poly edges for pavers and decorative concrete, steel for hardpack, trip edges anywhere there are curbs.
  • Blowers almost always need high-flow hydraulics. Standard flow is roughly 15 to 25 gpm; high flow runs above that. Match the numbers before you book.
  • Reserve the machine and the attachment together, by the week or the season, before the first storm is on the forecast.